Promo Price: GHC 250
Normal Price: GHC350
KINDLY FILL THE FORM BELOW TO ORDER.
- PLEASE ENSURE YOU ARE FULLY READY FOR PRODUCT AND THE MONEY TO PAY AT THE POINT OF DELIVERY IS AVAILABLE BEFORE YOU PLACE ORDER.
Product sellpoints
NitroOBD2 is a plug-in transmission box device to improve engine performance.
NitroOBD2 is easy to install. Plugs directly into the car’s OBD2 connector, NitroOBD2 fits all car models from 1996 onwards.
It works based on OBD2 protocol to remap the car computer ECU. When driving 200 kilometers, NitroOBD2 will adjust the car, according to the driver’s habits, and keep remapping the ECU to increase the engine performance.
What does nitroobd2 do?
According to your driving habits, NitroOBD2 increases the performance of your car with a newly configured computer ECU on the car.
As you drive more km/miles, it updates the configuration. Thus, maintaining the increase in power and torque of the vehicle.
What is the nitroobd2 power fuel optimization device?
NitroOBD2 is a power fuel optimization device that can be plugged into your car’s OBD2 connector to increase the performance of your car.
When it is plugged into the OBD2 connector, nitroobd2 receives and sends messages with ECU data from the car computer ECU.
NitroOBD2 adjusts boost, fuel volume, injection timing and pressure to increase the performance of your car.
The NitroOBD2 powered fuel optimizer does not exceed the manufacturer’s requirements, it only works within the engine tolerances.
NitroOBD2 discovers the hidden power of your car. NitroOBD2 does not damage the engine and car computer ECU or produce any negative impact on the factory settings.
NitroOBD2 does not change any settings permanently. To return to the original settings on the car, just unplug NitroOBD2 from the OBD2 connector.
nitroobd2 discovers the hidden power of your car.
– Up to 35% more power
-Up to 25% more torque
NitroOBD2 is very easy to use.
Plug the nitroobd2 plug into your car’s OBD2 connector and turn on the ignition for 30 seconds, the engine starts.
NitroOBD2 settings optimize your car to a better state, even if each parameter is different for each vehicle.
No additional adjustments are required. NitroOBD2 will recognize your car and your driving habits after approximately 200 km/150 mph.
NitroOBD2 adjusts itself to suit your car and matches it perfectly.
NitroOBD2 works on the basis of the changes in the form of signals to the ECU. As a result, it changes the entire configuration.
The main difference between the nitroobd2 power fuel optimization and mapping adjustment methods is that the nitroobd2 power fuel optimization device is easy to disassemble,
Unplug and return to factory settings. NitroOBD2 is a cheap, convenient and safe tuning.
Remapping is a permanent change to your car. It is expensive for the tuner and you can’t remove it.
The engine protection function equipped by nitroobd2 is 100% safe for your car engine.
NitroOBD2 makes SMD technology on printed circuit boards, and NitroOBD2 power fuel optimization devices are of high quality.
Installation and calibration
1. Insert the car key.
2. Find your car’s OBD2 connector, and then plug in nitroobd2.
3. This stage is critical, turn the car key. (Do not start the car)
4. Press the reset button of nitroobd2 for about 5 seconds. After releasing the button, wait for about 30-54 seconds (nitroobd2 will communicate with the ECU to establish a connection)
5. Start the engine.
6. NitroOBD2 will recognize your car and your driving habits, and after about 200 km/150 mph, NitroOBD2 will adjust itself to match your car for more fuel-efficient perfection.
nitroobd2 diesel: red
Nitroobd2 gasoline: yellow
For LPG equipment
Does your car have an OBD2 connector?
On-board diagnostics, or “OBD,” is a computer system built into all 1996 and later light-duty cars and trucks, as required by the Clean Air Act Amendments of 1990.
The OBD system is designed to monitor some of the main engine components including those responsible for controlling emissions performance.
Cars that support OBD;
Sold in the U.S. after January 1, 1996
Sold in the EU after January 1, 2001
Diesel engines sold after January 1, 2003
Where is the OBD2 connector located in your car?
1. The cylindrical area next to the driver, below the dashboard and below the steering wheel.
2. Next to the driver, below the dashboard, between the driver’s side door and the steering column.
3. Next to the driver, below the instrument panel, between the steering column area and the center console.
4. Driver side instrument panel, instruments/surface area, steering column and center console.
5. Driver’s side instrument panel, instrument/surface area, between the driver’s side door and steering column.
6. Center console, vertical plane away from the center line of the vehicle.
7. Center console, a vertical plane on the centerline of the vehicle or on the passenger side of the center console.
8. Center console, at the level of the front passenger area.
Package Contents:
– NitroOBD2 Power Fuel Optimizer
– English user manual